
For "attenuation coefficient" as it applies to electromagnetic theory and telecommunications see propagation constant. For the "mass attenuation coefficient", see the article mass attenuation coefficient.
The attenuation coefficient is a quantity that characterizes how easily a material or medium can be penetrated by a beam of light, sound, particles, or other energy or matter. A large attenuation coefficient means that the beam is quickly "attenuated" (weakened) as it passes through the medium, and a small attenuation coefficient means that the medium is relatively transparent to the beam. Attenuation coefficient is measured using units of reciprocal length.
The attenuation coefficient is also called linear attenuation coefficient, narrow beam attenuation coefficient. Although all four terms are often used interchangeably, they can occasionally have a subtle distinction, as explained below.
Overview
The attenuation coefficient describes the extent to which the intensity of an energy beam is reduced as it passes through a specific material. This might be a beam of electromagnetic radiation or sound.

It is used in the context of Xrays or Gamma rays, where it is represented using the symbol \mu, and measured in cm^{−1}.

It is used in the context of neutrons and nuclear reactors, where it called macroscopic cross section (although actually it is not a section dimensionally speaking) being represented using the symbol \Sigma, and measured in m^{−1}.

It is also used for modeling solar and infrared radiative transfer in the atmosphere, albeit usually denoted with another symbol (given the standard use of \mu = \cos(\theta) for slant paths).

In the case of ultrasound attenuation it is usually denoted as \alpha and measured in dB/cm/MHz.^{[1]}^{[2]}

The attenuation coefficient is widely used in acoustics for characterizing particle size distribution.^{[1]}^{[2]} A common unit in this contexts is inverse metres, and the most common symbol is the Greek letter \alpha.

It is also used in acoustics for quantifying how well a wall in a building absorbs sound. Wallace Sabine was a pioneer of this concept. A unit named in his honor is the sabin: the absorption by a 1squaremetre (11 sq ft) slab of perfectly absorptive material (the same amount of sound loss as if there were a 1squaremetre window).^{[3]} Note that the sabin is not a unit of attenuation coefficient; rather, it is the unit of a related quantity.
A small linear attenuation coefficient indicates that the material in question is relatively transparent, while a larger value indicates greater degrees of opacity. The linear attenuation coefficient is dependent upon the type of material and the energy of the radiation. Generally, for electromagnetic radiation, the higher the energy of the incident photons and the less dense the material in question, the lower the corresponding linear attenuation coefficient will be.
Definitions and formulae
The measured intensity I of transmitted through a layer of material with thickness z is related to the incident intensity I_0 according to the inverse exponential power law that is usually referred to as Beer–Lambert law:

I(z) = I_{0} \, e^{\int_0^z \alpha(z') \, \operatorname dz'},
where z denotes the path length. The attenuation coefficient is \alpha (z'). If it is uniform, the situation is referred to as linear attenuation and the law simplifies:

I(z) = I_{0} \, e^{\alpha \, z},
The Half Value Layer (HVL) signifies the thickness of a material required to reduce the intensity of the emergent radiation to half its incident magnitude. It is from these equations that engineers decide how much protection is needed for "safety" from potentially harmful radiation. The attenuation factor of a material is obtained by the ratio of the emergent and incident radiation intensities I/I_0.
The linear attenuation coefficient and mass attenuation coefficient are related such that the mass attenuation coefficient is simply \alpha/\rho, where \rho is the density in g/cm^{3}. When this coefficient is used in the BeerLambert law, then "mass thickness" (defined as the mass per unit area) replaces the product of length times density.
The linear attenuation coefficient is also inversely related to mean free path. Moreover, it is very closely related to the absorption cross section.
Attenuation versus absorption
The terms "attenuation coefficient" and "absorption coefficient" are generally used interchangeably. However, in certain situations they are distinguished, as follows.^{[4]}
When a narrow (collimated) beam of light passes through a substance, the beam will lose intensity due to two processes: The light can be absorbed by the substance, or the light can be scattered (i.e., the photons can change direction) by the substance. Just looking at the narrow beam itself, the two processes cannot be distinguished. However, if a detector is set up to measure light leaving in different directions, or conversely using a nonnarrow beam, one can measure how much of the lost intensity was scattered, and how much was absorbed.
In this context, the "absorption coefficient" measures how quickly the beam would lose intensity due to the absorption alone, while "attenuation coefficient" measures the total loss of narrowbeam intensity, including scattering as well. "Narrowbeam attenuation coefficient" always unambiguously refers to the latter. The attenuation coefficient is always larger than the absorption coefficient, although they are equal in the idealized case of no scattering.
See also
References

^ ^{a} ^{b} ISO 209981:2006 "Measurement and characterization of particles by acoustic methods"

^ ^{a} ^{b} Dukhin, A.S. and Goetz, P.J. "Ultrasound for characterizing colloids", Elsevier, 2002

^ "Wallace Clement Sabine". Acoustics Engineering. Retrieved 20111108.

^ Bohren,C. F. and Huffman, D.R. "Absorption and Scattering of Light by Small Particles", Wiley, (1983), isbn= 0471293407
External links

Absorption Coefficients α of Building Materials and Finishes

Sound Absorption Coefficients for Some Common Materials

Computations for Radio Wave Propagation

Tables of XRay Mass Attenuation Coefficients and Mass EnergyAbsorption Coefficients from 1 keV to 20 MeV for Elements Z = 1 to 92 and 48 Additional Substances of Dosimetric Interest
This article was sourced from Creative Commons AttributionShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, EGovernment Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a nonprofit organization.