World Library  
Flag as Inappropriate
Email this Article


Article Id: WHEBN0005500097
Reproduction Date:

Title: Washboarding  
Author: World Heritage Encyclopedia
Language: English
Subject: Gravel road, Dirt road, Suspension (vehicle), Roads, Washboard
Collection: Geotechnical Engineering, Road Hazards, Roads
Publisher: World Heritage Encyclopedia


Washboarding or corrugation[1] is the occurrence of periodic, transverse ripples in the surface of gravel and dirt roads. Washboarding occurs in dry, granular road material[2] with repeated traffic, traveling at speeds above 5 mph.[3] Washboarding creates an uncomfortable ride for the occupants of traversing vehicles and hazardous driving conditions for vehicles that travel too fast to maintain traction and control.[4]


Washboarding or corrugation of roads comprises a series of ripples, which occur with the passage of wheels rolling over unpaved roads at speeds sufficient to cause bouncing of the wheel on the initially unrippled surface. Most studies of washboarding pertain to granular materials, including sand and gravel.[1][5] However, other work suggests that the phenomenon may occur in material, which has some binding of particles, e.g. clayey soils.[6]

Highway department experts in the mid-1920s were aware that traffic volume and speed were primary causes of corrugations on gravel roads and cited the role of drive wheels tossing material as a factor.[7][8]

Laboratory-scale studies of the phenomenon typically employ a wheel or a blade, which is towed behind a pivot point and allowed to bounce over the material studied as it follows a circular path in a pan, holding the material. These studies have investigated a variety of granular and viscous, even fluid, materials.[1][6] In the laboratory, washboarding has been studied for a range of parameters, including the thickness and grain size of the material for varied wheel sizes, shapes and masses. Experiments produced ripples for each parameter, above a threshold speed, when the wheel (or blade) began to bounce.[1] Experiments also show that the pattern can move either against the direction of motion or in the direction of motion. They also show that a passive, non-driving wheel suffices to create corrugations and that displacement of material, rather than ejection is the dominant mechanism.[1]

Several articles addressing real-life washboarding on roads cite South Dakota Local Transportation Assistance Program (LTAP) Special Bulletin #29, “Dealing with Washboarding,” by Ken Skorseth.[2][9] These sources attribute washboarding to three causes: dry granular materials, vehicle speeds, and the quality of the granular material. Other cited causes include vehicle speed, traffic volume and hard acceleration or braking. Also, the source claims that light vehicles have a bigger effect on producing washboarding than heavy trucks.[9]

Examples of corrugation in different soil types


Highway department guidance for avoiding washboarding suggests that choice of gravel can be key to mitigating washboarding. They cite "sieve analysis" tests that use a series of screens or sieves to characterize the sizes of particles contained within a gravel sample. Highway department guidance suggests a range of particle sizes from stones that are in the 1 inch (25 mm) range, mixed with progressively finer particles to include a small fraction of fine particles that bind the larger particles together. They also mention the role of equipment that can re-blend and smooth surfaces that have corrugated.

In 1925, the Nevada Department of Highways advocated mitigating corrugations with crushed pit-run gravel, using material 1 inch (25 mm) and smaller, including only the fines from crushing.[7] Contemporaneous advice from Colorado was to use a well-graded gravel, not exceeding 1.25 inches (32 mm) and including 25-40% fines passing a 0.25 inches (6.4 mm) sieve, but not more than 5% passing a #10 (2.0-mm)[10] sieve.[11] The maintenance advice from Colorado was to drag or grade the road frequently, applying light volumes of new gravel with minimal sand content and providing good drainage with a crown. The same source advises reduction of traffic speed.[8]

Guidance based on South Dakota LTAP Special Bulletin #29 and FHWA guidance (2000) from the same source[12] suggests that the surface gravel "should be a blend of stone, sand and fines that will compact into a dense, tight mass with an almost impervious surface." It emphasizes the proper gradation of gravel—100%[12] passing the 0.75 inches (19 mm)) sieve—to have fractured stone to "interlock" and 4-15% fines[12] passing the #200 (75-μm)[10] sieve[11] to act as a binder and create cohesiveness in the gravel; substituting other binders, such as clay is also recommended. Alternately, one can incorporate reclaimed asphalt in a half-and-half blend with quarried gravel to improve the binding properties of the surface. For existing washboarded surfaces, the bulletin recommends using a grader to cut and blend existing material to a depth one inch or more below the bottom of the washboarded segment and then add the new material into the top layer. Useful equipment includes a blade with rotating scarifying teeth or a replaceable bit-type cutting edge attached to the moldboard blade of the earth-moving equipment.[9]


  1. ^ a b c d e Taberlet, Nicolas; Morris, Stephen W.; McElwaine, Jim N. (2007). "Washboard Road: The dynamics of granular ripples formed by rolling wheels" (PDF). Phys. Rev. Lett. 99: 068003.  
  2. ^ a b Nevada Transportation Technology Transfer Center (Summer 2002). "Causes and cures for washboarding" (PDF). Streetwise 2 (1). University of Nevada. Retrieved 2014-11-26. 
  3. ^ Rehmeyer, J. (August 18, 2007). "Road Bumps: Why Dirt Roads Develop a Washboard Surface". Science News (Science Service, Inc.). Retrieved 2014-12-25. 
  4. ^ US Fed News Service (2010). "Motorists warned of washboarded surfaces on backcountry gravel roads". The Associated Newspapers of Ceylon Ltd. Retrieved 2014-12-25. 
  5. ^ Bitbol, A.-F.; Taberlet, N.; Morris, S.; McElwaine, J. (2009), "Scaling and dynamics of washboard road", Phys. Rev. E 79: 061308,  
  6. ^ a b Hewitt, I. J.; Balmforth, N. J.; McElwaine, J. N. (2012), "Granular and fluid washboards" (PDF), J. Fluid Mech. (Cambridge University Press),  
  7. ^ a b Honeysteele, P.L. (1925), "Permanent Highways", Fourth Biennial Report of the Department of Highways—1923-1924, Carson City: State of Nevada, pp. 85–87 
  8. ^ a b Hinkle, A.H. (November 1924), "Prevention of Corrugations", Colorado Highways 3 (11), pp. 7, 11 
  9. ^ a b c Skorseth, Ken (2004). "Washboarding" (PDF). Are We There, Yet?. South Carolina Department of Transportation. 
  10. ^ a b Subcommittee: E29.01 (2013). "Nominal Dimensions, Permissible Variations for Wirecloth of Standard Test Sieves (U.S.A.)" (PDF). ASTM E11 - 13. ASTM International. Retrieved 2014-12-28. 
  11. ^ a b Subcommittee: E29.01 (2013). "Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves". ASTM E11 - 13. ASTM International. p. 9. 
  12. ^ a b c Skorseth, Ken; Selim, Ali A. (November 2000), Gravel Roads Maintenance and Design Manual (PDF), FHWA, South Dakota Local Transportation Assistance Program, pp. 20–21 

This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from World eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.